Reasons Your fiat 500 abarth key 500 Key Fob Won't Work

A key fob for the fiat replacement key Cost 500 makes it simple to open doors and start your vehicle. There are a myriad of reasons the fob could stop working. This includes a dead battery water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement fiat panda key replacement Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Modern key fobs have a very limited range of operation, and must be within some feet of the vehicle in order to function. If you are far from your vehicle, and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a new one from a reputable brand such as Panasonic, Duracell, or Energizer. You can find them in the local hardware store or on the internet.

After you've replaced the battery of your coin cell You can test it by standing close to your fiat doblo key fob replacement 500 and pressing the buttons. The car should blink its parking lights and the key fob should be able to operate the lock and unlock buttons.

If the fob's remote doesn't work after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If that doesn't work the fob might require reprogramming by an experienced locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and then cease to function. It's not the best idea to soak the fob in water however, don't give it up if you accidentally drop it in water or forget to take it out of your pants pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Next test the fob to see if it works. If the key isn't working, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and hasn't been programmed to your vehicle it is likely to need to be replaced completely. This is a simple procedure that can be handled by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition in your vehicle. The locksmith will also need to program your fob into the car's system. This is a simple and inexpensive process which can be completed in the next day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop working is because it's out of range. The remote's range is of 30 feet. Therefore, when you're too far from your car it won't be able to respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If your fob won't work after replacing the battery for the coin, also called a "button", "watch" or "button", it may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob can resolve the issue. There are instructions on how to start fiat 500 without key to do this on the majority of automobiles by searching YouTube or consulting the owner's manual.

You may need to replace the metal clips that hold the coin battery in place. If they lose tension, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might be out of sync with your vehicle because of hardware or software problems. This can be a major headache, but you can usually fix it by visiting a local dealer or auto locksmith to reprogram your fob. In some instances the software might require reinstallation into your body control modules.

Interference

In addition to a dead coin battery The key fob might not be able to receive or transmit a signal due to interference. This may happen if the keyfob's location is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons the key fob may not function include a poor connection to the buttons or the internal chip or water damage.

If the key fob has suddenly stopped working, in the middle of the night and you've tried everything you can at home to solve it e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will clear out any remaining electricity and then restart the car's computers. This could allow you to get your key fob working again. If the issue continues, you should seek the advice of an expert technician. They'll be able identify the root cause of your issue.